Megatron Suture

For sealing joints, cracks, connections, conjugations, adjacencies


Material description:

      Dry construction mixture of special cement, silica sand granulometry certain active chemical additives used for waterproofing seams, joints, cracks in concrete junctions. For cracks, seams, joints and the like usually knock an indenting, then moisturize and ground it with "Megatron penetrative"solution . Indenting tightly invest solution "Megatron Seam" and treated with a solution"Megatron penetrative".

Features:

  • has high strength;

  • non- shrinking solutions;

  • reduced rate of sediment deformation;

  • has good adhesion to concrete, metal, brick and natural stone;

  • Used in conjunction with Megatron penetrative material;

  • Material is environmentally friendly, radiation safe;

  • Approved for usage in drinking water supply.

Scope:

  • Hydro precast concrete structures (foundation blocks, lift shafts, balcony slabs, introduction communications);

  • Waterproofing of monolithic concrete structures (joints, abutment, crack, putting communications);

  • Waterproofing industrial structures (joints, abutment, crack, putting communications);

  • Hydro plants agricultural sector (joints, abutment, crack, putting communications);

  • Waterproofing of water management structures (joints, abutment, crack, putting communications);

  • Waterproofing of mining and extraction facilities (seams abutment, crack, putting communications);

  • Waterproofing treatment plants (seams abutment, crack, putting communications).

Recommendations for Application:

      Indenting carry the entire length of the crack using hammer mills or mechanically or otherwise. Cross-section should be at least 25x25 mm.See abutment of the wall / floor to ensure the necessary strength of water resistance. Material is applied with a large-section cracks (indenting) in layers up to 30 mm at a time. Pre-moistened material fills the cavity of the joint, crack or indenting hand or by spatula. Also at closing large cracks with the aim of saving the material is allowed to add a small fraction of the material washed gravel (5-10mm.) In an amount of 25-30% by volume. The filled indenting is recommended for further processing using the "Megatron penetrative." The consumption in terms of dry mixture at chopping 25x25 mm is approximately 1.7 kg / linear meter. It should be noted that an increase indenting-section cracks is under increasing the material consumption.

   The dry mixture is mixed with water in a ratio of 1 kg. 160 grams of a mixture of water 6: 1 for six of the dry mix one part water by volume. Pour water into the dry mixture. Stir by hand for 1-2 minutes. The mixture becomes the consistency of clay. As close as you can use the solution for 15-30 minutes. Use the material mixing it regularly. The further water addition is not allowed.

The cost of ready-made solution:

   Consumption "Suture Megatron" is 1.7 kg / linear meter at indenting 25 x 25 mm.

Storage:

   Shelf life 18 months at temperatures from 20 to + 60º C in the original packaging is not broken.

Safety measures:

   Use rubber gloves  in process of working (skin irritation is possible) and safety glasses. Material  becomes heated in process of mixing.

Characteristic Value Conformity ДСТУ

1

Appearance

Loose dark gray powder, without additives

ДСТУ Б В.2.7-126-2011

ДСТУ БВ.2.7-171:2008

2

Humidity wt% 0,5÷0,7

ДСТУ Б В.2.7-126-2011

ДСТУ БВ.2.7-171:2008
3

The term of hardening min.

Beginning

End

 

20÷35

35-60

ДСТУ Б В.2.7-126-2011

ДСТУ БВ.2.7-171:2008

4

Bulk density g / cm3

1,35

ДСТУ Б В.2.7-126-2011

ДСТУ БВ.2.7-171:2008

5

Improving the performance of water resistance, degree 5

ДСТУ Б В.2.7-126-2011

ДСТУ БВ.2.7-171:2008

6

Possible increase in compressive strength% до 10

ДСТУ Б В.2.7-126-2011

ДСТУ БВ.2.7-171:2008
7 Mark on water resistance, W 14÷20

ДСТУ Б В.2.7-126-2011

ДСТУ БВ.2.7-171:2008

8

Increasing resistance, Nb cycles

At least 100 ÷ 150

ДСТУ Б В.2.7-126-2011

ДСТУ БВ.2.7-171:2008

9

Resistance of concrete to acids High

ДСТУ Б В.2.7-126-2011

ДСТУ БВ.2.7-171:2008

10

Resistance to alkalis in concrete High

ДСТУ Б В.2.7-126-2011

ДСТУ БВ.2.7-171:2008
11 Resistance of concrete to the action of oil High

ДСТУ Б В.2.7-126-2011

ДСТУ БВ.2.7-171:2008
12 Ultraviolet No effect

ДСТУ Б В.2.7-126-2011

ДСТУ БВ.2.7-171:2008
13 Temperature at application ◦S +5

ДСТУ Б В.2.7-126-2011

ДСТУ БВ.2.7-171:2008
14 Operating temperature ◦S -60 ÷ +130

ДСТУ Б В.2.7-126-2011

ДСТУ БВ.2.7-171:2008
15 Storage conditions In the dry indoors in sealed containers

ДСТУ Б В.2.7-126-2011

ДСТУ БВ.2.7-171:2008
16 Shelf life 18

ДСТУ Б В.2.7-126-2011

ДСТУ БВ.2.7-171:2008